石转轮+CO 、沸石转轮+RTO 、危废暂存间、催化燃烧设备
地图 - 热线
15392885678

- 服务热线 - 15392885678 15069779222

低浓度VOCs别硬烧,先“浓缩”再催化才省钱

发布人:武汉润华环保设备有限公司 发表时间:2026-10-19

喷漆房、印刷线、涂布线有个共性:风量大、浓度低,常常只有 200–300 mg/m?。这种废气直接进燃烧设备,燃料费能烧到老板心疼;不处理又过不了排放口。破局点不是换更大炉子,而是“先浓缩、后销毁”。

Spray painting rooms, printing lines, and coating lines have a common feature: high air volume and low concentration, often only 200-300 mg/m?. This kind of exhaust gas directly enters the combustion equipment, and the fuel cost can burn to the boss's heart; Without treatment, it cannot pass through the discharge outlet. The breakthrough point is not to replace the furnace with a larger one, but to 'concentrate first, then destroy'.

20230919074017718

沸石转轮负责把低浓度废气“压扁”:蜂窝状疏水沸石持续吸附 VOCs,转轮缓慢转动,吸附区、脱附区、冷却区三段切换;用小股热风把污染物从转轮上吹下来,原来 2 万风量的废气,可浓缩成 2000–3000 风量、浓度提升 5–20 倍的高浓气。

The zeolite wheel is responsible for flattening low concentration exhaust gas: the honeycomb shaped hydrophobic zeolite continuously adsorbs VOCs, and the wheel rotates slowly, switching between the adsorption zone, desorption zone, and cooling zone; Using a small stream of hot air to blow pollutants down from the impeller, the original 20000 air volume of exhaust gas can be concentrated into a highly concentrated gas with an air volume of 2000-3000 and a concentration increase of 5-20 times.

后面接 CO(催化燃烧):高浓气进换热器预热,再入催化床,在 250–400℃ 借助催化剂把 VOCs 氧化成 CO? 和 H?O。相比直接燃烧 800℃ 以上,CO 能耗低一大截;催化剂选对了,起燃温度还能再降。

Next is CO (catalytic combustion): The high concentration gas is preheated in the heat exchanger and then enters the catalytic bed. At 250-400 ℃, VOCs are oxidized to CO? And H? O with the help of a catalyst. Compared to direct combustion above 800 ℃, CO energy consumption is significantly lower; If the catalyst is selected correctly, the ignition temperature can be further lowered.

选系统别只问“能不能达标”,要看四件事:

Don't just ask if you can meet the standards when choosing a system, you need to consider four things:

废气组分:含氯、含硫、硅酮、高沸点树脂会毒化沸石和催化剂,得先小试;

Waste gas components: chlorine containing, sulfur-containing, silicone, and high boiling point resins can poison zeolites and catalysts, so small-scale testing is necessary first;

转轮疏水性:水性漆/高湿废气要用疏水改性沸石,不然转轮“喝饱水”不吸附;

Hydrophobicity of the impeller: Water based paint/high humidity exhaust gas should use hydrophobic modified zeolite, otherwise the impeller will not adsorb when it is "saturated with water";

脱附温度与风速:脱附不干净=转轮慢慢失效,脱附太猛=催化床超温;

Desorption temperature and wind speed: Unclean desorption=slow failure of the impeller, excessive desorption=overheating of the catalytic bed;

安全联锁:LEL 浓度监测、旁路、急停、防爆电气一个不能少,低浓度≠没爆炸风险。

Safety interlock: LEL concentration monitoring, bypass, emergency stop, and explosion-proof electrical components are essential. Low concentration ≠ no explosion risk.

运行里非常容易被忽略的是运维:定期高温再生、换过滤棉、查催化剂活性,比“买完就不管”重要得多。设备不是黑盒,懂物料特性再去谈配置,运行费能差出一辆小车钱。

The most easily overlooked aspect during operation is maintenance: regular high-temperature regeneration, replacement of filter cotton, and checking catalyst activity are much more important than "just buying and then ignoring". Equipment is not a black box. Understanding the characteristics of materials before discussing configuration can result in a difference in operating costs compared to a small car.

本文由沸石转轮+CO友情奉献.更多有关的知识请点击:http://www.tdyhhb.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is contributed by the zeolite wheel and CO friendship For more information, please click: http://www.tdyhhb.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

相关产品
Related products
相关新闻
Related News
Address

地址

武汉市黄陂区汉口北大道21号金马凯旋家居CBD原辅材料市场L02
Contact Us

服务热线

15392885678

15069779222
Mailbox

邮箱

1432716203@qq.com

微信二维码

微信公众号

微信二维码

微信公众号

//

截屏,微信识别二维码