石转轮+CO 、沸石转轮+RTO 、危废暂存间、催化燃烧设备
地图 - 热线
15392885678

- 服务热线 - 15392885678 15069779222

转轮前先过“预处理关”

发布人:武汉润华环保设备有限公司 发表时间:2026-11-14

沸石转轮+RTO这套组合,常被当成“低浓度大风量废气的标准答案”。真到涂装、印刷、医药包衣现场,先垮的往往不是炉子,是转轮前端——漆雾、水汽、硅氧烷没拦住,沸石孔道半年堵死,后面RTO再猛也救不回效率。

The combination of zeolite wheel and RTO is often regarded as the "standard answer for low concentration and high air volume exhaust gas". When it comes to painting, printing, and pharmaceutical coating sites, the first thing to collapse is often not the furnace, but the front end of the wheel - paint mist, water vapor, and silicone are not blocked, and the zeolite pores are blocked for half a year. No matter how fierce the RTO is later, it cannot save the efficiency.

98b1e61a-a7f9-4f7a-8799-4c3b9be70d3c

先说工艺链怎么走:

First, let's talk about the process chain:

废气收集→多级过滤/除雾/降温除湿→沸石转轮吸附(洁净气直排)→200℃左右热风脱附→小风量高浓度气进RTO(760–850℃氧化)→蓄热陶瓷换热→部分热风回脱附段。

Exhaust gas collection → multi-stage filtration/dehazing/cooling dehumidification → zeolite rotary adsorption (clean gas direct discharge) → hot air desorption at around 200 ℃ → low air volume high concentration gas enters RTO (760-850 ℃ oxidation) → thermal storage ceramic heat exchange → partial hot air desorption section.

转轮不是“吸附率越高越好”,是“活得久才划算”。

The wheel is not 'the higher the adsorption rate, the better', but 'it's worth living longer'.

一、预处理是命门,不是附件

1、 Preprocessing is fate, not attachment

颗粒物:进转轮前≤1mg/m³,漆雾类黏性气溶胶≤0.1mg/m³(新国标GB 20101—2025口径);

Particulate matter: ≤ 1mg/m ³ before entering the wheel, and viscous aerosols such as paint mist ≤ 0.1mg/m ³ (new national standard GB 20101-2025 caliber);

过滤等级:F8起步,喷涂线加漆雾毡+袋式+中效三级,别用单层粗网凑数;

Filtering level: Starting from F8, spray line with paint mist felt+bag type+medium efficiency level three, do not use single-layer coarse mesh to make up the numbers;

温度:进气宜≤40℃,超温沸石吸附容量掉,表冷或混风先降温;

Temperature: The intake temperature should be ≤ 40 ℃. If the adsorption capacity of the over temperature zeolite decreases, the surface cooling or mixed air should be cooled first;

湿度:相对湿度控60%以下,高湿天水分子抢孔位,浓缩倍数从12–15倍掉到7–9倍;

Humidity: The relative humidity should be controlled below 60%. In high humidity water, molecules compete for pore positions, and the concentration factor drops from 12-15 times to 7-9 times;

毒物:硅氧烷、含硫、高沸点树脂(>200℃)建议前置保护床/碱洗/冷凝,否则孔道不可逆占满。

Toxic substances: Siloxanes, sulfur-containing, high boiling point resins (>200 ℃) must be pre protected with a bed/alkaline wash/condensation, otherwise the pores will irreversibly fill up.

二、转轮本体盯四个数

2、 The wheel body focuses on four numbers

脱附温度:180–220℃常规,高沸物工况定期300℃高温再生;

Desorption temperature: 180-220 ℃. Conventional, high boiling point conditions require periodic high-temperature regeneration at 300 ℃;

面风速:1–3m/s,太快穿透、太慢设备虚胖;

Face wind speed: 1-3m/s, too fast penetration, too slow equipment bloating;

压降:正常<800Pa,超1500Pa先查前置过滤,别急着换轮;

Pressure drop: Normal<800Pa, if it exceeds 1500Pa, check the pre filtration first and do not change the wheel in a hurry;

密封条:每3个月查磨损,泄漏直接拉低浓缩比,2–3年整体换。

Sealing strip: Check for wear every 3 months, if there is a leak, directly lower the concentration ratio, and replace it as a whole every 2-3 years.

三、RTO侧别只盯“炉温”

3、 RTO side, don't just focus on "furnace temperature"

炉膛760–850℃,停留≥1s,热回收>95%;

Furnace at 760-850 ℃, retention time ≥ 1s, heat recovery>95%;

切换阀响应<1.5s,蓄热室压差偏差<5%;

Switching valve response<1.5s, accumulator pressure difference deviation<5%;

蓄热体压降>2000Pa清陶瓷,5年左右评估更换;

If the pressure drop of the thermal storage body is greater than 2000Pa, the ceramic will be evaluated and replaced in about 5 years;

浓缩气进炉前LEL在线监测:超10%LEL报警联锁,超25%开应急排放/稀释,不靠人工盯屏。

Online monitoring of LEL before concentrated gas enters the furnace: if the LEL exceeds 10%, an alarm interlock will be triggered, and if it exceeds 25%, emergency discharge/dilution will be activated, without relying on manual screen monitoring.

四、选型前先采72小时工况

4、 Before selecting, operate under a 72 hour working condition

别只给“平均浓度”。要拉满负荷、换班、烘漆、停机前后峰值曲线。

Don't just give 'average concentration'. Peak curves before and after full load, shift change, baking, and shutdown are required.

风量1万–20万m³/h、入口<1000mg/m³:转轮+RTO正解;

Airflow of 100000-200000 m ³/h, inlet<1000mg/m ³: Wheel+RTO positive solution;

浓度<100mg/m³浓缩后不够自持:别硬上,考虑直接燃烧或活性炭;

Concentration<100mg/m ³ is not self-sustaining after concentration: do not harden, consider direct combustion or activated carbon;

含氯含卤:RTO材质升2205双相钢/哈氏合金,加急冷防二噁英;

Containing chlorine and halogen: RTO material is made of 2205 duplex steel/Hastelloy alloy, with rapid cooling to prevent dioxins;

间歇波动大:五室RTO+缓冲罐,别用三室硬扛。

Large intermittent fluctuations: Five chamber RTO+buffer tank, do not use three chamber hard handling.

五、运行期三张表

5、 Three tables during the operation period

每班:转轮压差、脱附风温、RTO炉温、LEL值、风机电流;

Each shift: Wheel pressure difference, desorption air temperature, RTO furnace temperature, LEL value, fan current;

每月:密封条、过滤芯、蓄热体压差、CEMS校准;

Monthly: Sealing strip, filter element, pressure difference of thermal storage body, CEMS calibration;

每年:高温再生、转轮效率复核、联锁演练(模拟超浓度切阀)。

Annual: High temperature regeneration, wheel efficiency review, interlock drill (simulating over concentration cut-off valve).

验收别只看出口浓度。看三件事:

Don't just look at the export concentration for acceptance. Look at three things:

满负荷连续72h,NMHC稳定达标(核心区≤30mg/m³);

Continuous full load for 72 hours, NMHC stable compliance (key areas ≤ 30mg/m ³);

转轮进出口浓度差算真实吸附率;

Calculate the true adsorption rate based on the concentration difference between the inlet and outlet of the impeller;

联锁动作有记录——不是“能报警”,是“阀真动、炉真停”。

The interlocking action is recorded - it is not "able to sound an alarm", but "the valve really moves and the furnace really stops".

沸石转轮+RTO的本质,不是两台设备拼一起,是把“脏风变干净、稀气变浓气、浓气烧干净、烧完余热回用”焊成一条链。预处理松一扣,后面全链代偿。

The essence of zeolite wheel+RTO is not to assemble two devices together, but to weld "dirty air becomes clean, lean gas becomes rich gas, rich gas is burned clean, and waste heat is reused after burning" into a chain. One slack in pre-processing, followed by full chain compensation.

相关产品
Related products
相关新闻
Related News
Address

地址

武汉市黄陂区汉口北大道21号金马凯旋家居CBD原辅材料市场L02
Contact Us

服务热线

15392885678

15069779222
Mailbox

邮箱

1432716203@qq.com

微信二维码

微信公众号

微信二维码

微信公众号

//

截屏,微信识别二维码