石转轮+CO 、沸石转轮+RTO 、危废暂存间、催化燃烧设备
地图 - 热线
15392885678

- 服务热线 - 15392885678 15069779222

沸石转轮+CO:低浓度废气,别硬烧,先浓缩

发布人:武汉润华环保设备有限公司 发表时间:2026-09-21

很多工厂的VOCs废气,浓度低得尴尬——两三百毫克每立方,直接烧吧,天然气消耗扛不住;不烧吧,排放不达标。沸石转轮+CO这套组合拳,就是专门解决这个矛盾的。

The VOCs emissions from many factories have an embarrassingly low concentration of two to three hundred milligrams per cubic meter. If we burn them directly, the natural gas consumption cannot withstand it; Don't burn it, the emissions are not up to standard. The combination of zeolite wheel and CO is specifically designed to solve this contradiction.

20230919074017718

核心逻辑一句话:先把低浓度废气“浓缩”成高浓度小风量,再烧,能耗天差地别。

The core logic is to first "concentrate" low concentration exhaust gas into high concentration small air volume, and then burn it, with vastly different energy consumption.

沸石转轮分三个区:吸附区、脱附区、冷却区,连续旋转。低浓度废气穿过吸附区,VOCs被沸石微孔截留,洁净气体直排;转轮转到脱附区,150到200度的热风把VOCs“蒸”出来,浓度瞬间提升5到25倍;再进CO炉,300到350度催化氧化,变成CO2和水。

The zeolite wheel is divided into three zones: adsorption zone, desorption zone, and cooling zone, and rotates continuously. Low concentration exhaust gas passes through the adsorption zone, VOCs are intercepted by zeolite micropores, and clean gas is directly discharged; Turning the wheel to the desorption zone, hot air at 150 to 200 degrees' vaporizes' VOCs, instantly increasing their concentration by 5 to 25 times; Further enter the CO furnace and undergo catalytic oxidation at 300 to 350 degrees Celsius to produce CO2 and water.

浓缩比是这套系统的命门。有研究实测,浓缩比从6提到18,甲苯去除率从98.2%掉到88%——浓缩比太高,脱附热量不够,沸石再生不有效,吸附效率跟着崩。所以工程上浓缩比一般控制在10到15倍,既降低后续燃烧负荷,又保证去除率。入口浓度100mg/m3、风速2m/s的工况下,再生温度180℃、转速2.8到5r/h、浓缩比8到12,去除率能稳在90%以上。

Concentration ratio is the lifeblood of this system. There are studies that have measured that when the concentration ratio increases from 6 to 18, the toluene removal rate drops from 98.2% to 88% - the concentration ratio is too high, the desorption heat is not enough, the zeolite regeneration is not thorough, and the adsorption efficiency decreases accordingly. So in engineering, the concentration ratio is generally controlled at 10 to 15 times, which not only reduces the subsequent combustion load but also ensures the removal rate. Under the conditions of an inlet concentration of 100mg/m3 and a wind speed of 2m/s, with a regeneration temperature of 180 ℃, a rotation speed of 2.8 to 5r/h, and a concentration ratio of 8 to 12, the removal rate can remain stable at over 90%.

转轮转速也是个精细活。转速太低,吸附区停留时间过长,污染物穿透;转速太高,脱附区停留时间不够,沸石再生不完全。实测数据是:2.2r/h时去除率85.4%,提到3.5r/h升到96.1%,再往上提,反而跌破90%。说白了,转速是吸附和脱附时间的平衡器,不是越快越好。

The rotational speed of the wheel is also a delicate activity. The rotational speed is too low, the residence time in the adsorption zone is too long, and pollutants penetrate; The rotational speed is too high, the residence time in the desorption zone is insufficient, and the zeolite regeneration is incomplete. The measured data shows that the removal rate is 85.4% at 2.2r/h, which increases to 96.1% at 3.5r/h, and then further increases, but drops below 90%. To put it simply, the rotational speed is the balancer of adsorption and desorption time, not the faster the better.

CO炉这边,催化剂是贵金属(Pt/Pd),起燃温度200到300度就够了。对比直接燃烧要600度以上,催化燃烧省的不是一点半点。空速设计一般不超过40000h-1,催化剂床层工作温度控制在700度以下,正常设计寿命超过8500小时。

On the CO furnace side, the catalyst is precious metal (Pt/Pd), and the ignition temperature of 200 to 300 degrees is sufficient. Compared to direct combustion, catalytic combustion saves more than 600 degrees. The airspeed design generally does not exceed 40000 h-1, the working temperature of the catalyst bed is controlled below 700 degrees, and the normal design life exceeds 8500 hours.

这套系统有三个坑,踩了就知道疼:

This system has three pitfalls, and stepping on them will cause pain:

第一,预处理不做够,沸石死给你看。进入转轮的废气颗粒物建议小于1mg/m3,湿度控制在80%以下,温度不超过40度。漆雾、粉尘、水雾随便哪个超标,沸石微孔堵了,几万块的转轮直接报废。前处理至少要G4+F7+F9三级过滤,颗粒物去除效率做到99%以上。

Firstly, if the pre-treatment is not sufficient, the zeolite will die and show you. The particulate matter in the exhaust gas entering the wheel must be less than 1mg/m3, with humidity controlled below 80% and temperature not exceeding 40 degrees. Paint mist, dust, and water mist all exceed the standard, zeolite micropores are blocked, and tens of thousands of dollars worth of wheels are directly scrapped. At least G4+F7+F9 three-stage filtration is required for pre-treatment, with a particle removal efficiency of over 99%.

第二,含硫、含卤、含硅、含磷的废气,别碰催化燃烧。这些物质是催化剂毒药,硫化物和卤化物会让贵金属永久失活,有机硅在高温下生成二氧化硅覆盖催化剂表面。上系统之前,先搞清楚废气里有没有这些东西。

Secondly, exhaust gases containing sulfur, halogen, silicon, and phosphorus should not be exposed to catalytic combustion. These substances are catalyst poisons. Sulfides and halides can permanently deactivate precious metals, while organosilicon generates silicon dioxide at high temperatures to cover the surface of the catalyst. Before installing the system, first check if there are these things in the exhaust gas.

第三,沸石不是万能吸附剂。甲醇、甲醛、C1到C4烷烃这类小分子,沸石根本抓不住;丙烯酸、丙烯腈这类易聚合单体,在沸石表面聚合了脱附不出来,转轮越用越废。

Thirdly, zeolite is not a universal adsorbent. Zeolite cannot capture small molecules such as methanol, formaldehyde, and C1 to C4 alkanes; Acrylic acid and acrylonitrile, which are easily polymerized monomers, cannot be desorbed on the surface of zeolites due to polymerization, and the more the spinning wheel is used, the more waste it becomes.

沸石转轮+CO的适用场景很明确:大风量、低浓度、组分稳定、不含催化剂毒物的有机废气。浓度低于500mg/m3的喷漆、胶水、印刷废气,这套组合能把运行成本压到非常低。浓度太高的,先考虑溶剂回收;组分太杂的,先做废气分类。

The application scenario of zeolite wheel+CO is very clear: organic waste gas with high air volume, low concentration, stable components, and no catalyst toxins. The combination of spray painting, glue, and printing exhaust gases with a concentration below 500mg/m3 can minimize operating costs. If the concentration is too high, consider solvent recovery first; If the components are too mixed, first classify the exhaust gas.

选这套系统,本质上是选一个“稳定”。参数设对了,它能连续跑好几年;预处理偷懒了,再贵的设备也是摆设。

Choosing this system is essentially choosing a 'stable' one. The parameters are set correctly, it can run continuously for several years; Preprocessing is lazy, even the most expensive equipment is just a decoration.

本文由沸石转轮+CO友情奉献.更多有关的知识请点击:http://www.tdyhhb.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is contributed by the zeolite wheel and CO friendship For more information, please click: http://www.tdyhhb.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message很多工厂的VOCs废气,浓度低得尴尬——两三百毫克每立方,直接烧吧,天然气消耗扛不住;不烧吧,排放不达标。沸石转轮+CO这套组合拳,就是专门解决这个矛盾的。

The VOCs emissions from many factories have an embarrassingly low concentration of two to three hundred milligrams per cubic meter. If we burn them directly, the natural gas consumption cannot withstand it; Don't burn it, the emissions are not up to standard. The combination of zeolite wheel and CO is specifically designed to solve this contradiction.

核心逻辑一句话:先把低浓度废气“浓缩”成高浓度小风量,再烧,能耗天差地别。

The core logic is to first "concentrate" low concentration exhaust gas into high concentration small air volume, and then burn it, with vastly different energy consumption.

沸石转轮分三个区:吸附区、脱附区、冷却区,连续旋转。低浓度废气穿过吸附区,VOCs被沸石微孔截留,洁净气体直排;转轮转到脱附区,150到200度的热风把VOCs“蒸”出来,浓度瞬间提升5到25倍;再进CO炉,300到350度催化氧化,变成CO2和水。

The zeolite wheel is divided into three zones: adsorption zone, desorption zone, and cooling zone, and rotates continuously. Low concentration exhaust gas passes through the adsorption zone, VOCs are intercepted by zeolite micropores, and clean gas is directly discharged; Turning the wheel to the desorption zone, hot air at 150 to 200 degrees' vaporizes' VOCs, instantly increasing their concentration by 5 to 25 times; Further enter the CO furnace and undergo catalytic oxidation at 300 to 350 degrees Celsius to produce CO2 and water.

浓缩比是这套系统的命门。有研究实测,浓缩比从6提到18,甲苯去除率从98.2%掉到88%——浓缩比太高,脱附热量不够,沸石再生不有效,吸附效率跟着崩。所以工程上浓缩比一般控制在10到15倍,既降低后续燃烧负荷,又保证去除率。入口浓度100mg/m3、风速2m/s的工况下,再生温度180℃、转速2.8到5r/h、浓缩比8到12,去除率能稳在90%以上。

Concentration ratio is the lifeblood of this system. There are studies that have measured that when the concentration ratio increases from 6 to 18, the toluene removal rate drops from 98.2% to 88% - the concentration ratio is too high, the desorption heat is not enough, the zeolite regeneration is not thorough, and the adsorption efficiency decreases accordingly. So in engineering, the concentration ratio is generally controlled at 10 to 15 times, which not only reduces the subsequent combustion load but also ensures the removal rate. Under the conditions of an inlet concentration of 100mg/m3 and a wind speed of 2m/s, with a regeneration temperature of 180 ℃, a rotation speed of 2.8 to 5r/h, and a concentration ratio of 8 to 12, the removal rate can remain stable at over 90%.

转轮转速也是个精细活。转速太低,吸附区停留时间过长,污染物穿透;转速太高,脱附区停留时间不够,沸石再生不完全。实测数据是:2.2r/h时去除率85.4%,提到3.5r/h升到96.1%,再往上提,反而跌破90%。说白了,转速是吸附和脱附时间的平衡器,不是越快越好。

The rotational speed of the wheel is also a delicate activity. The rotational speed is too low, the residence time in the adsorption zone is too long, and pollutants penetrate; The rotational speed is too high, the residence time in the desorption zone is insufficient, and the zeolite regeneration is incomplete. The measured data shows that the removal rate is 85.4% at 2.2r/h, which increases to 96.1% at 3.5r/h, and then further increases, but drops below 90%. To put it simply, the rotational speed is the balancer of adsorption and desorption time, not the faster the better.

CO炉这边,催化剂是贵金属(Pt/Pd),起燃温度200到300度就够了。对比直接燃烧要600度以上,催化燃烧省的不是一点半点。空速设计一般不超过40000h-1,催化剂床层工作温度控制在700度以下,正常设计寿命超过8500小时。

On the CO furnace side, the catalyst is precious metal (Pt/Pd), and the ignition temperature of 200 to 300 degrees is sufficient. Compared to direct combustion, catalytic combustion saves more than 600 degrees. The airspeed design generally does not exceed 40000 h-1, the working temperature of the catalyst bed is controlled below 700 degrees, and the normal design life exceeds 8500 hours.

这套系统有三个坑,踩了就知道疼:

This system has three pitfalls, and stepping on them will cause pain:

第一,预处理不做够,沸石死给你看。进入转轮的废气颗粒物建议小于1mg/m3,湿度控制在80%以下,温度不超过40度。漆雾、粉尘、水雾随便哪个超标,沸石微孔堵了,几万块的转轮直接报废。前处理至少要G4+F7+F9三级过滤,颗粒物去除效率做到99%以上。

Firstly, if the pre-treatment is not sufficient, the zeolite will die and show you. The particulate matter in the exhaust gas entering the wheel must be less than 1mg/m3, with humidity controlled below 80% and temperature not exceeding 40 degrees. Paint mist, dust, and water mist all exceed the standard, zeolite micropores are blocked, and tens of thousands of dollars worth of wheels are directly scrapped. At least G4+F7+F9 three-stage filtration is required for pre-treatment, with a particle removal efficiency of over 99%.

第二,含硫、含卤、含硅、含磷的废气,别碰催化燃烧。这些物质是催化剂毒药,硫化物和卤化物会让贵金属永久失活,有机硅在高温下生成二氧化硅覆盖催化剂表面。上系统之前,先搞清楚废气里有没有这些东西。

Secondly, exhaust gases containing sulfur, halogen, silicon, and phosphorus should not be exposed to catalytic combustion. These substances are catalyst poisons. Sulfides and halides can permanently deactivate precious metals, while organosilicon generates silicon dioxide at high temperatures to cover the surface of the catalyst. Before installing the system, first check if there are these things in the exhaust gas.

第三,沸石不是万能吸附剂。甲醇、甲醛、C1到C4烷烃这类小分子,沸石根本抓不住;丙烯酸、丙烯腈这类易聚合单体,在沸石表面聚合了脱附不出来,转轮越用越废。

Thirdly, zeolite is not a universal adsorbent. Zeolite cannot capture small molecules such as methanol, formaldehyde, and C1 to C4 alkanes; Acrylic acid and acrylonitrile, which are easily polymerized monomers, cannot be desorbed on the surface of zeolites due to polymerization, and the more the spinning wheel is used, the more waste it becomes.

沸石转轮+CO的适用场景很明确:大风量、低浓度、组分稳定、不含催化剂毒物的有机废气。浓度低于500mg/m3的喷漆、胶水、印刷废气,这套组合能把运行成本压到非常低。浓度太高的,先考虑溶剂回收;组分太杂的,先做废气分类。

The application scenario of zeolite wheel+CO is very clear: organic waste gas with high air volume, low concentration, stable components, and no catalyst toxins. The combination of spray painting, glue, and printing exhaust gases with a concentration below 500mg/m3 can minimize operating costs. If the concentration is too high, consider solvent recovery first; If the components are too mixed, first classify the exhaust gas.

选这套系统,本质上是选一个“稳定”。参数设对了,它能连续跑好几年;预处理偷懒了,再贵的设备也是摆设。

Choosing this system is essentially choosing a 'stable' one. The parameters are set correctly, it can run continuously for several years; Preprocessing is lazy, even the most expensive equipment is just a decoration.

本文由沸石转轮+CO友情奉献.更多有关的知识请点击:http://www.tdyhhb.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is contributed by the zeolite wheel and CO friendship For more information, please click: http://www.tdyhhb.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

相关产品
Related products
相关新闻
Related News
Address

地址

武汉市黄陂区汉口北大道21号金马凯旋家居CBD原辅材料市场L02
Contact Us

服务热线

15392885678

15069779222
Mailbox

邮箱

1432716203@qq.com

微信二维码

微信公众号

微信二维码

微信公众号

//

截屏,微信识别二维码